Thursday, September 2, 2010

Party People in DA House

Yo YO yoyo House Party ya'll.  Check this out.

Update #2: B1oH4z has shared a PSGroove AVR-USB-162 hex code that was compiled with a setting of 8mhz and using it Jasmin05 has confirmed the Olimex AT90USB162 works 100% now!

Update: martenbroadclk has now shared pre-compiled hex codes ready to burn followed shortly by hex codes for all boards, including both the original PSGroove release and CJPC's dev_bdvd patched version and Ps3Rips (actually Xantra, it appears now) has http://www.eurasia.nu/modules.php?name=News&file=article&sid=2604 the ATmega164PA PS JailBreak Schematics And PCB Layout.

Recently we reported that the PS JailBreak PS3 modchip was successfully cloned, and today the PSGroove PS3 exploit arrives!

PSGroove is an open-source reimplementation of the PSJailBreak exploit for AT90USB and related microcontrollers.

The PSGroove for now allows the very same features as the PSJailBreak but without backup manager support, you can also now remove the dongle.

The original PSJailbreak dongle had a patch that would trigger the lv1 panic hypercall if the dongle wasn't in the list of connected devices.

CJPC has also detailed HERE how to patch it to allow for the proper mountpoint dev_bdvd to be mounted enabling the playback of backup games and posted a patched version below for those lazy.

Download: http://github.com/psgroove/psgroove / PSGroove PS JailBreak PS3 Exploit [Mirror] / PSGroove PS JailBreak PS3 Exploit (Patched) / PSGroove PS JailBreak PS3 Exploit Hex Codes (AT90USBKEY boards) / PSGroove PS JailBreak PS3 Exploit Hex Codes (All Boards) / PS JailBreak Schematics And PCB Layout

It should work on:

- AT90USB162
- AT90USB646
- AT90USB647
- AT90USB1286
- AT90USB1287
- ATMEGA32U4
- ... and maybe more.









Cloning

The repository uses the LUFA library as a submodule. To clone, use something like:

git clone git://github.com/psgroove/psgroove.git
cd psgroove
git submodule init
git submodule update

Configuring

Chip and board selection can usually be handled in the Makefile. In particular, update the MCU, BOARD, and F_CPU lines. Suggested values:

Teensy 1.0:
MCU = at90usb162
BOARD = TEENSY
F_CLOCK = 16000000

Teensy++ 1.0:
MCU = at90usb646
BOARD = TEENSY
F_CLOCK = 16000000

Teensy 2.0:
MCU = atmega32u4
BOARD = TEENSY
F_CLOCK = 16000000

Teensy++ 2.0:
MCU = at90usb1286
BOARD = TEENSY
F_CLOCK = 16000000

AT90USBKEY / AT90USBKEY2:
MCU = at90usb1287
BOARD = USBKEY
F_CLOCK = 8000000

Board-specific notes

Teensy boards only have one LED, so it will turn off when the exploit succeeds rather than turn green. Older Teensy 1.0 boards also have the polarity inverted. In general, a LED should do something when the board is powered, and do something different when the exploit works.

Building

On Linux, use the AVR GCC toolchain (Debian/Ubuntu package: gcc-avr). On Windows, WinAVR should do the trick.

make clean
make

Programming

Now program psgroove.hex into your board and you're ready to go. For the AT90USBKEY and other chips with a DFU bootloader preinstalled, you can get the dfu-programmer tool, put your board in programming mode, and run

make dfu

For the Teensy boards, you probably have to use the Teensy Loader software.

Using

To use this exploit:

- Hard power cycle your PS3 (using the switch in back, or unplug it)
- Plug the dongle into your PS3.
- Press the PS3 power button, followed quickly by the eject button.

After a few seconds, the first LED on your dongle should light up. After about 5 seconds, the second LED will light up (or the LED will just go off, if you only have one). This means the exploit worked! You can see the new "Install Package Files" menu option in the game menu.

Notes

A programmed dongle won't enumerate properly on a PC, so don't worry about that.

This software is not intended to enable piracy, and such features have been disabled. This software is intended to allow the execution of unsigned third-party apps and games on the PS3.

4 comments: